Superior: Stop living in the past and update your old Ford Super Duty fog lights with top-of-the-line LED projector housings. The XB LED projector fog lights from Morimoto not only deliver a super wide and perfectly distributed 2400-lumen beam of beautiful white light, but they’ll also shine a spotlight on modernized front-end of your truck. Throw in the fact that they’re as reliable as the sunrise and bright enough to turn night back into day, and we have ourselves a winner. Cruise through the TRS parking lot, and you’re sure to see some of the guys here rocking Morimoto fog lights on their own trucks.
Swap In: The XB LED projector fog light upgrades are fully compatible with all Ford Super Duty and Excursion models from 1999 to 2016. Just take out your original halogen units and replace them using all of the stock mounting locations. Then all you have to do is use the integrated height adjuster bar to dial the beam of your new fog lights just the way you like it. You can find a list of known applications in the compatibility section below.
Plug n Play Functionality: At TRS, we know what you’re looking for because we’re auto enthusiasts just like you. We can assure you this Ford Super Duty LED retrofit kit for converting fog lights is wired to make life easier. The XB LED fogs work without special wiring, come with everything you need to connect, and are compatible with your original cabin controls.
Driven: The whole idea here is to find a product that helps you see better on the road and look great doing it. Luckily, Morimoto XB LEDs check both boxes. These Super Duty LED projector fog lights deliver 2,400 lumens of pure white light capable of cutting through the mistiest and murkiest conditions. Innovative projector-based optics make it possible to produce a wider, more evenly distributed beam that allows you to not only see further, but also to see more of the road. These aftermarket LED headlight upgrades are SAE, DOT, and ECE approved, too.
Long-Lasting: Whether you’re going from home to work and back again in bad weather or going full tilt in rugged off-road conditions, it’s good to know your fog lights will be there when you need them most. Morimoto’s commitment to excellence is evident in the latest generation of Ford Super Duty projector headlight upgrades and of course, these fog lights. From durable polycarbonate lenses to ultra-light powder-coated cast aluminum housings, everything about these fogs is geared toward standing the test of time. We’ve tested various models in all sorts of extreme conditions and found the housing is capable of protecting internal components by creating a nearly impenetrable shield to moisture and debris.
Word on the Street: Don't just take our word for it, check out these Install & Review videos that previous customers have put together! Everybody loves a good YouTube demo, so check it out HERE!, HERE!, HERE!, and HERE!
Leading Source: TRS has been raising the bar in automotive lighting solutions for over a decade. We’re proud of the reputation we’ve built as real car guys who offer the best line of products at the lowest prices anywhere. Plus, we back it up with the most dedicated and passionate team in the industry. Have a question about Ford Super Duty LED projector headlights/fog lights? Require technical assistance? Interested in wholesale? Contact us today!
FOG LIGHTS: 2x Type SD Morimoto XB LED
WIRING: Plug-n-Play Connection Kit
OPTIONAL: Lamin-X Yellow Film Kit
WARRANTY: 10 Years
SWAG: Morimoto Decal
REPLACES FORD PART #: 6C3Z-15200-AA, 6C3Z-15200-BA, 7C3Z15200AA, 7C3Z15201AA, BC3Z15200A, BC3Z15201A, XL3Z13466A
FORD EXCURSION: 1999-2016
FORD SUPERDUTY: 1999-2016
CERTIFICATIONS: DOT, ECE, SAE
NOTE: 1999-2010 Trucks Req. Minor Modification!
INPUT SOCKET: Sealed H10 Male
WEATHER RATING: IP67 Waterproof
LENS MATERIAL: High Impact Polycarb (UV-Resistant)
SHELL / HEAT SINK: Powder Coated Cast Aluminum
LIGHT SOURCE: 3x Nichia
LED OPTICS: Kuria-2 Fog-Projection Lens
INTENSITY: 1,200lm (raw; each)
COLOR: 5500K (Pure White)
Great quality product, nicely packaged as well. I had a Morimoto HID kit in my factory fog lights before, but I thought these would look nicer and go better with my retrofit projector headlight assemblies. They do look great, but the light output compared to my previous HID kit, is considerably less. However, the light that is there, is better used than what I had before, so that's a plus.
Installation was a little time consuming because these came with no instructions and the "install guide" on both the TRS and Morimoto website's are just some generic guide for how to plug the wires into a socket and apply the yellow film to the lens if you bought that to go along with the lights (so, basically useless).
My truck is lifted 8", and I adjusted the aiming screw to the same height as my factory lights were at (which was already aimed down some). However, at that setting, these were shining light up into space, higher up than my headlights even were. LOL. I had to aim these all the way down, and crank my adjustment screw as far down/tight as it would go, to get the light to a usable height.
Now that it's all adjusted correctly, they do work well, and combined with my HID retrofit headlights, it's a pretty good combo at night, and aesthetically looks good too.
Great lights, they were a nice drop in fit minus the round hole needing to be filed square on certain year trucks, for the $200 it seems like they could come with their own hardware.
Bought these to try on my 2004 Ford Ranger. Minor modification required, change the adjustment hole from round to square. Should fit 04-06 Rangers with square fog lights.
Once the modification was made, they easily replaced the factory fog lamps. Nice white light with sharp cut-off.
I put these on my 2008 f250 and was very happy with the results. They're much brighter then the factory fog light bulbs, but because of the projectors have a pretty distinct cut off line. Haven't had any oncoming traffic flash their lights at me, which used to happen with hid bulbs in the fogs. Definitely worth purchasing.
I got these today and went thru the install. As of now it's still daylight so the night time review will be updates later.
Nice product packaging wrapped with bubble wrap. I was surprised that the connectors were not installed but recalled these fit more SD trucks so I'm sure the polarity changed over the years. I ended up taking off the smaller bumper support bracket that is behind the OEM fog assemblies. Once the OEM fogs were out the swap was a tad time consuming only to get the OEM housing out of the brackets. Remember this stuff is plastic so don't be too forceful. I set the adjustment screw to the same thread protrusion as it was when I removed the OEM housing. So far these LED housing look great and have great light output. Tonight will be a test drive to check for overall vision and impressions.