What's that you say? There's a hole burning in your wallet? The OEM Stage IV system is packed out with exotic options that combine to make this our most expensive pre-bundled kit for reasons you won't regret. If you're an OEM kinda guy, this is where it's at! The mix of premium brands here will undoubtedly result in a very reliable, unique, and high performance set of headlights.
Shrouds: Basically, they're the trim piece that adds the finishing touch to your new headlight retrofit. They cover the projector after it’s installed to restore the factory-finished look inside the housings. With so many different shapes, sizes, and designs available; we really recommend picking one that suits the geometry inside of your headlights, and also your personal preference on how they look. Check out all of the projector shroud options we offer, and take your pick!
OEM Ballasts: From Matsushita or Denso, these have a virtually instant warm up time, bringing the HID bulbs to their full intensity within 2-3 seconds. As long as they stay dry, these should also last forever. The optional ballast potting service makes them "bomb proof" by preventing moisture damage and enhancing their warranty coverage.
Philips 85122 D2S Bulbs: Are the benchmark for high quality 4300K HID lamps. With their extra long life span, unmatched precision, and high luminosity - they've been an OE benchmark for ten years. These days, you can upgrade to the super Osram CBI or NightBreaker bulbs for even more luminosity and white light. If you've got the money, go for it! We take pride in being one of the few retailers that only sells genuine OEM products.
Wire Harness: As one of the most important parts in any HID lighting upgrade; don't skimp out when it comes to your wiring. It doesn't matter how good your ballasts are. How good your bulbs are. If your harness is a piece of crap, when it gives out your headlights are gonzo. Morimoto’s harnesses are the best on the market and easily worth their premium price compared to cheaper alternatives. No matter which one is right for your application, the harness features triple-sealed central relay packs, 14ga stranded copper wiring, over-molded fittings, and plug-n-play functionality. This will ensure everything properly (and permanently) works with your vehicle’s original in-cabin controls.
Optional Canbus Harnesses: Instead of a traditional relayed harness that draws power from the battery, Morimoto’s Standalone Canbus harnesses use two individual sub-harnesses to keep a load on the factory wiring. Recommended for vehicles that recognize when a bulb is out, these contain a series of capacitors and resistors to trick the car into thinking nothing has changed and help you avoid annoying "bulb out" warnings. We generally recommend them for use on most modern European applications instead of normal harnesses since they do a great job at providing stable power to the ballasts and canceling any warnings.
Optional LED Halos: Though LED halos may not be for everybody, if you’re looking for the cleanest, most simple, most reliable setup, we highly recommend the Morimoto XSB Halos. Not only are they the brightest, most uniformly lit halos currently on the market, but they double as a switchback turn signal with your blinker circuit. The integrated controllers are extremely easy to setup with only three wires (white, amber, and ground) and allow you to run the white mode continuously until interrupted by the signal – at which point they will blink amber. Once the signal stops, the XSB ring will automatically switch back to its pure white mode.
Optional Housing Sealant: Protection is priceless! When you're putting together a set of high-end headlights, the last thing you want is moisture in 'em the first time it rains outside. RetroRubber is the most effective way to make sure the original seal is fully restored. For the small price, why anybody wouldn’t prevent their new headlights from fogging up is beyond us. It’ll be the best twelve bucks you’ve ever spent.
Trusted: For more than a decade, we've worked hard to earn our reputation. Car guys world-wide know that TRS carries the internet's best selection of high performance automotive lighting products at the best prices and we've got the best, most knowledgeable team of real enthusiasts to help back it up. If we sell it, then you bet we've put it to the test on our own cars. Need a recommendation on parts for your project? Got a tech question? Wholesale inquiry? Contact Us
PROJECTORS: 2x OEM Options
SHROUDS: 2x Your Preference
D2S HID BULBS: 2x Philips or Osram
WIRE HARNESS: 1x Your Preference
WARRANTY: 3 Years (excluding moisture damage)
OPTIONAL HOUSING SEALANT: 1x Morimoto RetroRubber
OPTIONAL LED HALOS: 2x Morimoto XSB 2.0
APPLICATIONS: Universal / Size Allowing
CAPABILITIES: Low & High Beam
PROJECTOR DIMENSIONS: Varies by Model
PROJECTOR LENS: Varies by Model
MINIMUM HOUSING DEPTH: Varies by Model
WIRE HARNESS: Match your original bulb size
SHROUDS: Most except "Mini" models
LED HALOS: Varies according to shroud style
OPERATING RANGE: -40C to +125C
OE BALLAST INPUT: 12VDC
OE BALLAST OUTPUT: 85V AC
OE BALLAST MAX V: 25kV (at start-up)
OE BALLAST LIFESPAN: 2000 Hours
OE 4300K BULBS: Warm White Color
OE 5500K BULBS: Pure White Color
LUMINOSITY: 3200-3500lm total (depends on bulbs)
Overall, a full great kit. Now, if you own a Mitsubishi Lancer 2008+, choose the Morimoto 3Five ballasts, since there is an exact space under the headlight to mount it with screws, plus they are waterproof. I choosed Densos, which are quite large, non waterproof and difficult to mount in Lancer's engine bay, my mistake! I sealed them as possible.. Great shrouds' and projectors' quality. Also, great customer support. Highly recommended. Many thanks TRS!